Dodge Caravan, Grand Caravan, Voyager Front Wheel Hub Bearing Replacement

Here is another great set of instructions for the do-it-yourselfers out their. These instructions came from a 1992 Dodge Caravan, however they will work on Caravan, Voyager, Grand voyager, Grand caravan, and many other Chrysler products.

Purchase this hub & bearing assembly for only $59.99 each at:

This hub and bearing assembly is being used on certain Caravan, Voyager and Mini Ram Vans. This unit is serviced as a complete assembly, and is attached to the steering knuckle by four mounting screws that are removed from the rear of the knuckle assembly.

Removal: Remove cotter pin, nut lock, and spring washer.

Loosen hub nut while the vehicle is on the floor with the brakes applied. The hub and drive shaft are splined together through the knuckle (bearing) and retained by the hub nut.

Raise vehicle.

Remove hub nut, washer, and wheel and tire assembly.

Disconnect tie rod end from steering arm.

Remove clamp bolt securing ball joint stud into steering knuckle.

Remove caliper guide pins and separate caliper assembly from braking disc. SUPPORT CALIPER WITH WIRE HOOK AND NOT BY HYDRAULIC HOSE. Remove brake rotor.

Separate ball joint stud from knuckle assembly. Pull knuckle assembly out and away from drive shaft. NOTE: Care must be taken not to separate the Inner C/V joint during this operation. Do not allow drive shaft to hang by inner C/V joint, drive shaft must be supported.

Remove the four hub and bearing assembly mounting screws from rear of steering knuckle.

Remove hub and bearing assembly. Replacement of the grease seal is recommended whenever this service is performed.


Install new hub and bearing assembly and tighten screws in a criss-cross pattern to 45 foot pounds. CAUTION: Knuckle and bearing mounting surfaces must be smooth and completely free of foreign material or nicks.

Position new seal in recess.

Assemble tool and install seal. CAUTION: During any service procedures where knuckle and drive shaft are separated, thoroughly clean seal and wear sleeve and relubricate BOTH components.

Lubricate the full circumference of the seal (and wear sleeve) with Multi-Purpose Lubricant.

Install drive shaft through hub, then install steering knuckle assembly on lower control arm ball joint stud.

Install original (or equivalent) ball joint to knuckle clamp bolt, torque to 70 foot pounds.

Install tie rod end into steering arm, tighten nut to 35 foot pounds torque and install cotter key.

Install brake rotor.

Carefully lower caliper over braking disc and guide hold-down spring under machined abutment on knuckle assembly. Install guide pins and tighten to 18-26 foot pounds. When installing guide pins, use extreme caution not to cross the threads or to overtighten as you can break these bolts.

Install washer and hub nut after cleaning foreign matter from threads.


Install spring washer, nut lock, and new cotter pin. Wrap cotter pin prongs tightly around nut lock.

Install wheel and tire assembly. Tighten wheel nuts to 85 foot pounds.

This is just an outline that we found online. we can provide instructions from the factory service manual simply by calling us toll-free at 1-866-770-2771 or please e-mail us:

We are a ASE certified automotive technicians with many years in the field. If you need help installing any of our products please do not hesitate to call or e-mail us. Thanks and I hope this helps.

Please rate our guide, we want to find out if we’re helping you!!!

View Our Other Instructional Guides

Visit Our eBay Store

Our 100% Positive Feedback


About Josh

I help manage the site here at Auto Repair Instructions. If you are having problems, then I am the one to contact.

Posted on June 1, 2007, in Dodge, Wheel Hub Bearing Replacement. Bookmark the permalink. 3 Comments.

  1. Will these instructions work for the front wheels on my 2002 dodge ram 1500 with rear wheel ABS only.

  2. THanks, these instructions for the caravan are vey similair to the ram pickup, however their are small differences. THis will give you a good overview of how to do it but the socket sizes adn torque will certainly be different. We can fax you manufacturere specific instructions for the ram if you like. We are working on getting a set on our site also. You cal call us at 1-866-770-2771 and we can provide the instructions for you. Thanks

  3. I have the same problem, but mine is a 2008 Dodge Grand Caravan, will these instructions be the same?

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: