Chevy Blazer 2WD Front Wheel Hub Bearing Replacement

Here is a great set of instructions submitted to us from one of our customers. These are very detailed and give you great insight into tackiling this very easy job. You may also call our team of ASE certified technicians with questions at 1-866-770-2771.

Shop for Hub Bearings

New Front Wheel Hub Bearing Assembly fits 2WD with ABS. Fitment for the following vehicles:

1998-2005 GMC S15 Jimmy 2WD w/ABS

1998-2005 Chevy S10 Blazer 2WD w/ABS

 ZR2 models are different, we do have them, please call us at 1-866-770-2771 and we can post a listing for you.

Instructions for replacing a front hub assembly on a 2001 2-wheel drive Chevrolet Blazer.

1. First determine which hub assembly is worn by removing the suspected tire/wheel.

2. I would recommend placing the vehicle on a jack stand for safety reasons. I placed mine on the boxed frame rail directly below the front door hinges. 3. After removing the tire, spin the rotor to verify the worn bearing assembly. If the assembly is worn when spinning, the rotor may sound like the disc pads are dragging, or grinding.

 4. To completely verify that the bearing is bad, remove the disc caliber assembly and spin again, if it’s still making noise you know the sealed hub assembly is bad. Hint: Place something on the floor to hold the caliber up in the air to take the stress off the brake line when you lift off the assembly. Also remove the lid on your Power Disc brake reservoir, this will allow the caliber to be easier to remove and re-install later.

5. To remove the brake caliber there are 2-18mm bolts that feed thru the caliber assembly from the back to the side you are looking at. This can be done with either an 18 mm box wrench or short socket with breaker bar. These are the 2 bolts on the caliber assembly, one on each end.

6. Next remove rotor by removing the 2 rotor retaining washers (mine were copper in color) that are on the lug nut studs. They look almost like an inverted star washers and side over the lug nut stud threads to hold the rotors in place.

7. Slide off rotor assembly pulling the rotor toward your body and over the wheel lug studs.

8. Do a visual inspection on the new hub assembly to get a feel for the removal of the old hub. This will give you an idea of how the hub assembly bolts to the spindle and the direction for the ABS wire lead routing.

 9. Unplug the ABS sensor wire; this connector is located up on the frame rail right above the upper control arm assembly. Just follow the wire up to the connector from the hub assembly.

 10. The hub assembly is held in place by 3-18mm bolts that feed thru the spindle from the backside. You can use a box wrench for the 2 lower bolts but I would recommend using a shallow socket for the top bolt. These bolts have some kind of lock tight or similar material to prevent them from backing out. I used a 3 lb. hammer to tap on the breaker bar/ box wrench to initially loosen. Make sure you are rotating the bolt counter clockwise direction when removing so as not to break any of the bolts off in the spindle.

11. After the 3 bolts are removed from the hub assembly you may have to hit the hub assembly a few times with the 3 lb. hammer to break it loose from the spindle. Mine was rusted together and needed a few taps with the hammer. Clean out any dirt/grime.

 12. Installation procedure is just the opposite of the removal.

13. Install the new hub assembly but I would place some lock tight on the threads of the 3 bolts. Tighten well with a few taps from the 3 lb. hammer. Careful don’t go crazy and break the bolts off.

**** If this were a 4-wheel drive vehicle, the axle shaft nut must be torqued properly. Please email us the year,make, and model of your vehicle and we would be glad to get your torque specs.

14. Reconnect the sensor plug.

15. Install rotor.

16. Install caliper assembly.

17. Replace wheel/ tire

 18. Don’t forget to put the lid back on the Power brake reservoir!

19. Total time about 1.5 hours for the first wheel, start to finish. Second wheel probably faster.

20. Test drive with a BIG SIMILE on your face because saved you a LOT of MONEY!

Example of TOOLS NEEDED:

18mm box wrench

Breaker bar

18mm shallow socket

 3lb. hammer

Bottle of lock tight

Jack stand

Needle nose pliers

Trouble light

I “can do” attitude

Note: Anyone who has done a disc pad replacement will have no problem doing this job.

Shop for Wheel Hub Bearings

View our 100% positive feedback

Please feel free to contact us via email or our toll free number 1-866-770-2771


About Josh

I help manage the site here at Auto Repair Instructions. If you are having problems, then I am the one to contact.

Posted on June 1, 2007, in Chevrolet, Wheel Hub Bearing Replacement. Bookmark the permalink. 3 Comments.

  1. Benjamin H. Adams III

    These directions were very helpful. The Chilton was a little vague and bearings seem to be a problem with these trucks. I was a little nervous being the first time to do this job, having a couple of young kids, an anxious wife looking on, and me cracking into our primary transportation, but these instructions did the trick and saved myself well needed money. Thanks for the time and effort invested, and making me look like a real shade tree machanic in front of the kids!

  2. Great product. Great price. Lifetime Guarantee. My vehicle drives 100% diffrent and 200% better, after, I installed the hub bearing. Though it takes a little long to recieve the part when you choose the payment options of check or money order the quality will make you forget. I will definetly order from for any other parts for my blazer and refer them to whoever asks. Everything except how long it took for my check to clear was very impressive to really say the least, but even then they gave me other payment options that i could do and I was stubborn. One way was going to a local walmart and geting something like a credit card to put money on. The customer service was outstanding. Anyways I had to leave a good comment after they did more than enough on their end.

  3. thomas walker

    what size socket and torque requirements for a 1998 4wd axle nut to replace wheel bearing do i need

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: